StucoLux™ Marmorino

$17.63$310.61

StucoLux™ Marmorino is a decorative, easy soft sheen polishing mineral based plaster. A creamy, fine sandy but smooth material, it glides on easily across any substrate. StucoLux™ Marmorino has very good interior and exterior durability and provides beautiful undulations of color depth in the final finish.

Clear
SKU: 000101 Category:
Approved Application Area Walls, Ceilings
Application Method Troweled
Clean Up Soap & Water
Approved Climate Rating Interior/Exterior
Consistency (Density) Medium Plaster
Available Sizes & Square Footage 5 Gallon Pail- 501 - 1000
1 Gallon Pail- 101 - 200
32 Oz Pail- <100
Durability Medium Traffic- Withstands normal wear & tear
Finish Texture Sand Grit
Intermix No
Manufacturer Faux Effects International
Product Line Silver Line
Sheen (Finish) Gloss
Shelf Life 60 - 120 Days
Approved Substrate Primed Drywall, Painted Drywall
Suggested Additives No
  • The lime and minerals contained in these products are non-toxic, durable and washable.
  • If water is splashed on the surface of unsealed StucoLux™ Marmorino it will darken the surface. The finish will lighten back to the original color once the water evaporates.
  • For added protection and water resistance apply a coat of StucoLux™ Seal and/or a coat of Olde World Venetian Wax™ if desired.
  • Ensure that the substrate is clean and free from oil, grease or any foreign substance.
  • Apply a coat of SetCoat®. *Important Note: The base coat must be thoroughly dry before proceeding.
  • Using a stainless steel application trowel, apply a sheer, very thin coat of StucoLux™ Marmorino to the surface using short upward strokes. This first coat should be applied as smoothly as possible; some graceful trowel lines are permitted in this first base layer. It is best to work wet into dry for this application. Natural imperfections will enhance the color patterns when StucoLux™ Marmorino is burnished during the final stages. Each light coat of StucoLux™ will dry fully in approximately 30 to 60 minutes depending on conditions.
  • To achieve the best results, a minimum of 2 coats is recommended. This will create good film formation and is needed for the finished look. Once the final coat has been applied and is 80% to 90% dry, the burnishing process may be started. Less pressure is needed when burnishing is started at this stage.
  • Holding a stainless steel burnishing trowel at a slight angle (20°-30º), run the edge of the trowel over the surface using light pressure. Cheesecloth, terrycloth or a plastic bag can also be used for the initial burnishing. Once this step is complete go back over the entire surface using increased pressure on the trowel. This will result in a high gloss shine.
  • Zero V.O.C.
  • The material has a general resistance to alkali, bacterial attack and exterior exposure
  • Resistant to abrasion and extreme changes in climate
  • Impervious to humidity, while still allowing the substrate to breathe
  • Do not discharge into drains, sewers, water retention areas, or other bodies of water
  • Contain the product by adding an absorbent (Oil-Dry, cat litter, etc.) before disposing of according to local regulations
  • Wear the appropriate protective gear (gloves, goggles, outerwear)
  • Store in a cool, dry location. Under optimum conditions product will remain stable for 12 – 24 months.
  • Do not apply in temperatures under 55°F, or in damp, cold or humid conditions.
  • Technical product- training through Faux Masters Studio workshop recommended

*Images and color swatches are for reference only. Please do not base any color purchases on images or swatches for actual color may vary slightly due to various monitor and graphics card settings.

Above attributes including finish texture and sheen depend on burnishing technique being applied to the product at the end of the application process.

Weight N/A

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.